FALCON Services

Examine and test wired electrical components such as motors, armatures, and stators, using measuring devices, and record test results. Operate or tend wire-coiling machines to wind wire coils used in electrical components such as resistors and transformers, and in electrical equipm More...

Hands-on operation of manual and automated hydroblasting equipment. Operation of special equipment, such as Ultra High-Pressure pumps. Operate equipment by energizing the pumping equipment and/or any specialized Hydroblasting and/or Chemical cleaning equipment, vacuum trucks and c More...

Setting up and calibrating NDT equipment. Conducting rigorous tests on structures and materials using non-destructive techniques. Developing and instituting bespoke NTD procedures for specified products and materials during and after manufacturing. Identifying structural and mate More...

Plans, assigns, schedules, and supervises the work of power linesmen, electricians, and helpers engaged in the construction, installation, maintenance, and repair of university power lines, electrical systems, fixtures, apparatus, and appliances; participates in the more difficult w More...

Reading and understanding scaffold blueprints. Providing input on scaffold planning. Transporting and unloading equipment. Erecting the scaffolding poles. Assembling the rest of the structure. Adding safety features like guard rails and safety netting. Performing intermittent More...

Applying lubricants to the moving parts of vehicle engines to prevent premature engine wear and ensure optimal engine performance. Lubricating wheel bearings to prevent excessive tire wear. Performing engine cleanings to prevent rust formation. Replacing cabin, fuel, air, and oil More...

Responsible for the plant effort on Safe Work Practices and optimal design for EHS. Responsible for the full scope of the Mechanical engineering project including budget control, schedule, and compliance with safety, environmental and sustainability requirements, to assure performa More...

- Directs, coordinates and supervises the Hydraulic/Pneumatic/Lubrication Systems installation, maintenance, testing and repair for Automotive Sheet area, including preparation of schedules and establishing work priorities. - Establishes/re-evaluates Preventive Maintenance schedule More...

Perform job responsibilities in Mechanical Engineering department. Understand mechanical seal design and selection, foundation components (sole plates, base plates, grouting), and pump/driver selection and installation. Performs calculations and reviews design of heat exchangers, More...

Installing and replacing valves and piping systems in industrial plants and other facilities Inspecting equipment for leaks or defects to determine if repairs are needed Testing and calibrating new equipment to ensure that it is operating properly Troubleshooting malfunctions in More...

Perform the disassembly and repair of mechanical control devices like valves and actuators such as thermostats, hydrants and regulators with the use of hand tools and power tools. Monitor and keep track of meter readings and installation data on meter cards, work orders, or field s More...

Inspecting and repairing pipes running to related equipment, such as radiators and HVAC units Providing estimates on the cost of parts and labor Making recommendations about necessary repairs or changes to plumbing systems Meeting with clients and/or customers to determine their More...

Conduct routine monitoring and maintenance to provide the highest possible availability of all analyzer systems Report problems and possible solutions to supervisor Receive instructions, work orders and safety permits for the troubleshooting, repair, calibration, replacement or ov More...

Maintenance ofton and ton EOT cranes Maintenance of pumps and pipe line work. Maintenance work done according to given schedule and as per instruction Planning people, Team management and Material requirement. Close monitoring and downtime analysis of day-to-day breakdown of m/c. More...

Building products on the assembly line according to drawings, instructions, or schematics. Following established safety and efficiency procedures to ensure that operations run smoothly. Inspecting assembled products for any faults or defects. Loading product pieces slated for ass More...

Install, maintain and repair hydraulic systems Read blueprints while diagnosing problems Perform preventative maintenance of hydraulic systems Perform welding, metal fabrication and electrical assembly Provide drawing review and suggestions related to part inspection and testing More...

Reading and interpreting building and engineering plans and drawings. Setting out work areas and determining the required materials. Using hand and power tools to cut and bend steel bars and mesh. Laying out steel bars, mesh, rods, and framework. Hoisting steel bars, mesh, and r More...

Review the overhaul, repair and test of products in accordance with approved repair procedures and determine required process and lead time to complete in accordance with the works order. Ensure that the customer is promptly informed and updated on all findings during repair or o More...

Responsible for repair and testing of various valves, including but not limited to ball valves, gate valves, butterfly valves, safety relief valves, etc. Perform disassembly, cleaning, inspection, measuring, reassembly and testing of valves at Flotech facilities and client location More...

Designing, manufacturing, and installing components that fulfill requirements. Analyzing problems or deficiencies and developing solutions to resolve them. Conducting experiments and evaluations to improve and innovate product designs. Creating plans and designs using CAD technol More...